spec no: dsan5572 rev no: v.3a date: jan/09/2015 page: 1 of 6 approved: wynec checked: allen liu drawn: l.q.xie e rp: 1101033401 oval solid state lamp part number: wp5603sidlk/sd/j3 hyper red features z outstanding material efficiency. z reliable and rugged. z high glass transition temperature epoxy. z rohs compliant. description the hyper red device is based on light emitting diode chip made from algainp. high glass transition temperature epoxy. package dimensions notes: 1. all dimensions are in millimeters (inches). 2. tolerance is 0.25(0.01") unless otherwise noted. 3. lead spacing is measured where the leads emerge from the package. 4. the specifications, characteristics and technical data descri bed in the datasheet are subject to change without prior notice .
spec no: dsan5572 rev no: v.3a date: jan/09/2015 page: 2 of 6 approved: wynec checked: allen liu drawn: l.q.xie e rp: 1101033401 selection guide notes: 1. 1/2 is the angle from optical centerline where the lumi nous intensity is 1/2 of the optical peak value. 2. luminous intensity/ luminous flux: +/-15%. * luminous intensity value is traceable to the cie127-2007 compliant national standards. absolute maximum ratings at ta=25c electrical / optical characteristics at ta=25c notes: 1.wavelength: +/-1nm. 2.forward voltage: +/-0.1v. 3.wavelength value is traceable to the cie127-2007 compliant national standards. 4.excess driving current and/or operating temperature higher t han recommended conditions may result in severe light degradation or premature failure. notes: 1. 1/10 duty cycle, 0.1ms pulse width. 2. 2mm below package base. 3. 5mm below package base. part no. dice lens type iv (mcd) [2] @ 20ma v iewing angle [1] min. typ. 2 1/2 hyper red (algainp) red semi diffused 1900 3800 80 (h) 40 (v) *1000 *2000 wp5603sidlk/sd/j3 symbol parameter device typ. max. units test conditions peak peak wavelength hyper red 640 nm i f =20ma d [1] dominant wavelength hyper red 625 nm i f =20ma ? 1/2 spectral line half-width hyper red 20 nm i f =20ma c capacitance hyper red 27 pf v f =0v;f=1mhz v f [2] forward voltage hyper red 2.2 2.8 v i f =20ma i r reverse current hyper red 10 ua v r = 5v parameter hyper red units power dissipation 84 mw dc forward current 30 ma peak forward current [1] 150 ma reverse voltage 5 v operating/storage temperature -40c to +85c lead solder temperature [2] 260c for 3 seconds lead solder temperature [3] 260c for 5 seconds
spec no: dsan5572 rev no: v.3a date: jan/09/2015 page: 3 of 6 approved: wynec checked: allen liu drawn: l.q.xie e rp: 1101033401 hyper red wp5603sidlk/sd/j3
spec no: dsan5572 rev no: v.3a date: jan/09/2015 page: 4 of 6 approved: wynec checked: allen liu drawn: l.q.xie e rp: 1101033401 packing & label specifications wp5603sidlk/sd/j3 terms and conditions for the usage of this document 1.the information included in this document reflects representative usage scenarios and is intended for technical reference only. 2.the part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. before product ion usage customer should refer to the latest datasheet for the updated specifications. 3.when using the products referenced in this docu ment, please make sure the product is being operated within the environmental and electrical limit s specified in the datasheet. if customer usage exceeds the specified limits, kingbright w ill not be responsible for any subsequent issues. 4.the information in this document applies to typical usage in consumer electronics applications. if customer's application has special reliabilit y requirements or have life-threatening liabilities, such as automotive or medical usage, please co nsult with kingbright representative for further assistance. 5.the contents and information of this document may not be reproduced or re-transmitted without permission by kingbright. 6.all design applications should refer to kingbr ight application notes available at http://www.kingbrightusa.com/applicationnotes
spec no: dsan5572 rev no: v.3a date: jan/09/2015 page: 5 of 6 approved: wynec checked: allen liu drawn: l.q.xie e rp: 1101033401
spec no: dsan5572 rev no: v.3a date: jan/09/2015 page: 6 of 6 approved: wynec checked: allen liu drawn: l.q.xie e rp: 1101033401
|
